Caution
-
Do not disassemble this product.
-
Do not remove its cover or its back. There are no user-serviceable parts inside.
-
Refer servicing to qualified service personnel only.
-
The use of controls, adjustments or procedures other than those specified in the guide may result in exposure to shock and/or electrical or mechanical hazards.
-
The Solo PRO contains an internal battery that is not designed to be removed by users. Note the following guidelines:
-
Required operation rated temperatures:
-
Charging: -5 to +35 degrees C
-
Discharging mode operation: -5 to +45 degrees C
-
-
10.5-17 VDC input powered operation: -5 to +45 degrees C
-
Avoid shorting the battery.
-
Do not immerse the unit in water.
-
Do not disassemble or deform the battery.
-
Do not expose the unit to fire and do not dispose of the unit and its internal battery in fire.
-
Avoid excessive physical shock or vibration of the unit.
-
Never use a unit that contains a battery that appears to have suffered abuse.
-
-
Store the Solo PRO in an environment with low humidity that is free from corrosive gas, and in temperatures from -20°C to 60°C, < 80% RH.
-
Use only the originally approved power supply adapter.
-
Use only the supplied accessories. Accessories (including cables) must not be replaced.
-
Do not use the product if there is any physical damage to the enclosure.
-
Keep all air inlets and outlets free of any objects that may interfere with the air flow for at least 10 cm.
-
It is normal for the product to become slightly hot during use. However, if the enclosure's temperature becomes unbearable to touch, turn the product off and contact support.
-
Avoid leaving the product unprotected in direct sunlight for more than five minutes.
-
Do not let the product come into contact with corrosive materials.
-
Do not let the product come into contact with explosive or corrosive gas.
-
Do not let the product come into contact with fire.
-
To prevent fire or shock hazard, do not expose the product to rain, liquid or moisture. The product can be used in light rain while it is protected by the belt pouch. The product is not designed to be used under water.
-
Only use the original LiveU pouch. Do not place the product in a non-LiveU bag.
-
If the LCD screen breaks for any reason, do not touch the glass.
The Solo PRO uses external cellular devices that should be operated according to the same rules and limitations. Do not operate the unit in an environment that might be susceptible to radio interference resulting in danger, specifically:
-
Areas where prohibited by the law
Follow any special rules and regulations and obey all signs and notices. Always ensure that the enclosure is turned off (the power switch is not lit) when instructed to do so, or whenever it can cause interference or danger.
-
Where explosive atmospheres might be present
Do not operate the Solo PRO in any area where a potentially explosive atmosphere might exist. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Be aware and comply with all signs and instructions.
-
It is not advisable to operate the Solo PRO at a refueling point or service station
Observe restrictions on the use of radio equipment in fuel depots (fuel storage and distribution areas), chemical plants or where blasting operations are in progress.
-
Areas with a potentially explosive atmosphere are often, but not always, clearly marked
Potential locations can include gas stations, below deck on boats, chemical transfer or storage facilities, vehicles using liquefied petroleum gas (such as propane or butane), areas where the air contains chemicals or particles, such as grain, dust or metal powders, and any other area where it would normally be advisable to turn off a vehicle’s engine.
-
Near medical and life support equipment
Do not operate the Solo PRO in any area where medical equipment or life support equipment exist, or near any equipment that may be susceptible to any form of radio interference. In such areas, the host communications device must be turned off. The Solo PRO could transmit signals that could interfere with this equipment.
-
On an aircraft, either on the ground or airborne
In addition to FAA requirements, many airline regulations state that wireless operations must be suspended before boarding an airplane. Ensure that the Solo PRO is turned off prior to boarding aircraft to comply with these regulations. The enclosure can transmit signals that could interfere with various onboard systems and controls.
-
While operating a vehicle
The driver or operator of any vehicle must not operate a wireless data device while in control of a vehicle. Doing so detracts the driver or operator's control and operation of that vehicle. In some countries, operating such communications devices while in control of a vehicle is an offense.
Comments
0 comments
Article is closed for comments.